Email has been sent to you , please check your spam/junk emails if you are unable to find the email.
Due to some internal error, the mail has not been sent.
Smoke alarms are powered by battery or by your home's electrical system. If the smoke alarm is powered by battery, it runs on either a disposable 9-volt battery or a non-replaceable 10-year sealed lithium battery. Alarms that receive their power from your home's electrical system (hardwired alarms) usually have a back-up battery that will need to be replaced once or twice a year.
There are many special features that can help protect you and your home, or make your safety products easier to maintain and operate. Many of these features are not well known by their name, so to learn more about specific features of a model, select it and view its detail page.
The price displayed here is a suggested retail price for this model. Please select ‘Find a Retailer’ to see the most current prices offered.
The Kidde KN-COPP-3 AC powered, plug-in carbon monoxide alarm utilizes sophisticated electronic components and unmatched sensor technology to protect you and your family from the dangers of CO. The KN-COPP-3 includes a 9V battery backup that provides continuous monitoring of CO levels, even during power outages, when AC-only units are not providing protection. The KN-COPP-3 will detect and store measured data of concentrated CO levels as low as 11 and up to 999 PPM with its peak level memory display. This alarm gives you several mounting options, including: direct-plug, a 6’ power cord or table top.
The Kidde KN-COPP-3 AC powered, plug in carbon monoxide alarm provides you and your family with warning signal to protect against dangerous levels of carbon monoxide in your home. This alarm is easily installed in any of your AC wall outlets. The digital display feature allows for easy viewing of carbon monoxide levels from 30-999PPM (parts per million). The KN-COPP-3 is UL listed and offers a 10-year life and a 10-year limited warranty.
Part Number (Ordering Number): 900-0076
The carbon monoxide alarm shall be Kidde Unit Number KN-COPP-3 (part number 900-0076) or approved equal. It shall be powered by a 120VAC, 60 Hz source along with a 9V battery back up. The temperature operating range shall be between 40˚F and 100˚F (4˚C and 38˚C) and the humidity operating range shall be 5% - 95% relative humidity. The CO sensor shall be of a fuel cell design and shall meet the sensitivity requirements of Underwriters Laboratories UL2034 Single and Multiple Station Carbon Monoxide Alarms. The unit shall provide accuracy of +/-20% + 15 parts per million (ppm) when reading CO concentration levels. The alarm shall include an attached plug that can be installed in any outlet following the UL/NFPA/Manufacturer’s recommended guidelines. The plug can be snapped into the back of the unit and shall be capable of being rotated so the alarm remains vertical independent of whether the electrical socket is mounted vertically or horizontally. In addition, the alarm plug will have an attached extension cord so the unit can be plugged into the wall outlet and then placed on a table or shelf. The unit shall incorporate a digital display that meets the sensitivity requirements of UL 2034. The display will identify the levels of CO in parts per million (ppm) once that level reaches 30ppm (i.e.: “abnormal” levels). The display will have a red dot in the lower right corner that will blink to indicate the normal operation. The alarm shall include a test button that will electronically simulate the presence of CO and cause the unit to go into alarm. This sequence tests the unit’s electronics to ensure proper operation. In accordance with UL 2034, the CO sensor will not alarm to levels of CO below 30 ppm and will alarm in the following time range when exposed to the corresponding levels of CO. 70 ppm CO concentration 60 – 240 minutes 150 ppm CO concentration 10 – 50 minutes 400 ppm CO concentration 4 – 15 minutes The alarm shall include a piezoelectric horn that is rated at 85 decibels at 10 feet. When the unit detects carbon monoxide, the alarm pattern will be four (4) short beeps – followed by five (5) seconds of silence – followed by four (4) short beeps. A number reading will appear on the digital display identifying the measured CO concentration (in ppm). The unit shall include a peak level memory feature that will store the peak CO level sensed since the unit was last reset. The peak CO level stored in the unit’s memory shall be displayed (in ppm) on the digital display by pressing the appropriate button on the unit. The memory shall also be capable of being reset. The unit shall also indicate a low battery warning utilizing each of the following methods: a brief alarm chirp occurring approximately once per minute and having “Lb” displayed on the digital display. The unit shall be listed to UL 2034. It shall also include a 10-year manufacturer’s limited warranty.